Cleanup

.gitignore

@@ -1,9 +1,4 @@
 .pio/*
 .vscode/*
 *.map
-test/*.md
-test/env/*
-test/configure_*.py
-TODO.md
 src_docs/_build/*
-data/*.min.htm

README.md

@@ -12,7 +12,7 @@
 
 GravityMon is a replacement firmware for the iSpindle firmware. It's 100% compatible with the iSpindle hardware design so it does not require any hardware changes. 
 
-Now also works with ESP32, either an ESP32 d1 mini or ESP32 c3 mini which both are pin compatible with ESP8266.
+Now also works with ESP32 d1 mini, ESP32 c3 mini, ESP32 S2 mini which both are pin compatible with ESP8266.
 
 Installation can be made using https://www.brewflasher.com or the web version at https://web.brewflasher.com
 

test/configure.py

@@ -1,91 +0,0 @@
-import requests
-import json
-
-host = "192.168.1.1"           # IP adress (or name) of the device to send these settings to
-id = "ee1bfc"                  # Device ID (shown in serial console during startup or in UI)
-
-def set_config( url, json ):
-    headers = { "ContentType": "application/json" }
-    print( url )
-    #print( json )
-    resp = requests.post( url, headers=headers, data=json )
-    if resp.status_code != 200 :
-        print ( "Failed "  )
-    else :
-        print ( "Success "  )
-
-#
-# Configure the device settings.
-#
-url = "http://" + host + "/api/config/device"
-json = { "id": id, 
-         "mdns": "gravmon",             # Name of the device
-         "temp-format": "C",            # Temperature format C or F
-         "sleep-interval": 30           # Sleep interval in seconds
-        }
-set_config( url, json )
-
-#
-# Configure the push settings. Blank means that its no used.
-#
-url = "http://" + host + "/api/config/push"
-json = { "id": id, 
-         "token": "",
-         "http-push": "http://192.168.1.1/ispindel",    # HTTP endpoint 
-         "http-push2": "",                              # HTTP endpoint2
-         "http-push-h1": "Content-Type: application/json",
-         "http-push-h2": "",
-         "http-push2-h1": "Content-Type: application/json",
-         "http-push2-h2": "",
-         "influxdb2-push": "",                          # InfluxDB2 settings
-         "influxdb2-org": "",
-         "influxdb2-bucket": "",
-         "influxdb2-auth": "" ,
-         "mqtt-push": "",
-         "mqtt-port": 1883,
-         "mqtt-user": "",
-         "mqtt-pass": ""
-         }  
-set_config( url, json )
-
-
-#
-# Configure the gravity settings.
-#
-url = "http://" + host + "/api/config/gravity"
-json = { "id": id, 
-         "gravity-formula": "",                         # If you want to set the gravity formula
-         "gravity-format": "G",
-         "gravity-temp-adjustment": "off"              # on or off
-         }
-set_config( url, json )
-
-#
-# Configure the hardware settings.
-#
-url = "http://" + host + "/api/config/hardware"
-json = { "id": id, 
-         "voltage-factor": 1.59,                        # Default value for voltage calculation
-         "temp-adjustment": 0,                          # If temp sensor needs to be corrected
-         "gyro-temp": "off",                            # Use the temp sensor in the gyro
-         "ota-url": ""                                  # if the device should seach for a new update when active
-        }
-set_config( url, json )
-
-#
-# Configure the gravity formula settings. If this is called the formula will be updated based on these measurements (zero angle values will be ignored)
-#
-url = "http://" + host + "/api/formula"
-json = { "id": id, 
-         "a1": 22.4, 
-         "a2": 54.4, 
-         "a3": 58, 
-         "a4": 0, 
-         "a5": 0, 
-         "g1": 1.000, 
-         "g2": 1.053, 
-         "g3": 1.062, 
-         "g4": 1, 
-         "g5": 1 
-         }
-set_config( url, json )