Updated docs to 0.9
This commit is contained in:
parent
7cafedd9bf
commit
aa4e3b5e8d
@ -12,6 +12,7 @@ Retrive the current configuation of the device via an HTTP GET command. Payload
|
|||||||
|
|
||||||
* ``temp-format`` can be either ``C`` or ``F``
|
* ``temp-format`` can be either ``C`` or ``F``
|
||||||
* ``gravity-format`` is always ``G`` (plato is not yet supported)
|
* ``gravity-format`` is always ``G`` (plato is not yet supported)
|
||||||
|
* ``ble`` is used to enable ble data transmission (only on esp32) simulating a tilt. Valid color names are; red, green, black, purple, orange, blue, yellow, pink
|
||||||
|
|
||||||
Other parameters are the same as in the configuration guide.
|
Other parameters are the same as in the configuration guide.
|
||||||
|
|
||||||
@ -22,6 +23,7 @@ Other parameters are the same as in the configuration guide.
|
|||||||
"id": "ee1bfc",
|
"id": "ee1bfc",
|
||||||
"ota-url": "http://192.168.1.50:80/firmware/gravmon/",
|
"ota-url": "http://192.168.1.50:80/firmware/gravmon/",
|
||||||
"temp-format": "C",
|
"temp-format": "C",
|
||||||
|
"ble": "color",
|
||||||
"brewfather-push": "http://log.brewfather.net/stream?id=Qwerty",
|
"brewfather-push": "http://log.brewfather.net/stream?id=Qwerty",
|
||||||
"token": "token",
|
"token": "token",
|
||||||
"http-push": "http://192.168.1.50:9090/api/v1/Qwerty/telemetry",
|
"http-push": "http://192.168.1.50:9090/api/v1/Qwerty/telemetry",
|
||||||
@ -53,9 +55,22 @@ Other parameters are the same as in the configuration guide.
|
|||||||
"gy": -6,
|
"gy": -6,
|
||||||
"gz": 4
|
"gz": 4
|
||||||
},
|
},
|
||||||
|
"formula-calculation-data": {
|
||||||
|
"a1":25,
|
||||||
|
"a2":30,
|
||||||
|
"a3":35,
|
||||||
|
"a4":40,
|
||||||
|
"a5":45,
|
||||||
|
"g1":1,
|
||||||
|
"g2":1.01,
|
||||||
|
"g3":1.02,
|
||||||
|
"g4":1.03,
|
||||||
|
"g5":1.04
|
||||||
|
},
|
||||||
"angle": 90.93,
|
"angle": 90.93,
|
||||||
"gravity": 1.105,
|
"gravity": 1.105,
|
||||||
"battery": 0.04,
|
"battery": 0.04,
|
||||||
|
"platform": "esp8266",
|
||||||
"runtime-average": 3.12
|
"runtime-average": 3.12
|
||||||
}
|
}
|
||||||
|
|
||||||
@ -65,6 +80,8 @@ GET: /api/device
|
|||||||
|
|
||||||
Retrive the current device settings via an HTTP GET command. Payload is in JSON format.
|
Retrive the current device settings via an HTTP GET command. Payload is in JSON format.
|
||||||
|
|
||||||
|
* ``platform`` can be either ``esp8266`` or ``esp32``
|
||||||
|
|
||||||
.. code-block:: json
|
.. code-block:: json
|
||||||
|
|
||||||
{
|
{
|
||||||
@ -72,6 +89,7 @@ Retrive the current device settings via an HTTP GET command. Payload is in JSON
|
|||||||
"app-ver": "0.0.0",
|
"app-ver": "0.0.0",
|
||||||
"id": "ee1bfc",
|
"id": "ee1bfc",
|
||||||
"mdns": "gravmon",
|
"mdns": "gravmon",
|
||||||
|
"platform": "esp8266",
|
||||||
"runtime-average": 3.12
|
"runtime-average": 3.12
|
||||||
}
|
}
|
||||||
|
|
||||||
@ -128,8 +146,20 @@ Retrive the data used for formula calculation data via an HTTP GET command. Payl
|
|||||||
}
|
}
|
||||||
|
|
||||||
|
|
||||||
|
GET: /api/clearwifi
|
||||||
|
===================
|
||||||
|
|
||||||
|
Will reset the wifi settings, leaving the rest unused.
|
||||||
|
|
||||||
|
For this to work you will need to supply the device id as a parameter in the request:
|
||||||
|
|
||||||
|
::
|
||||||
|
|
||||||
|
http://mygravity.local/api/clearwifi?id=<mydeviceid>
|
||||||
|
|
||||||
|
|
||||||
GET: /api/factory
|
GET: /api/factory
|
||||||
================
|
=================
|
||||||
|
|
||||||
Will do a reset to factory defaults and delete all data except wifi settings.
|
Will do a reset to factory defaults and delete all data except wifi settings.
|
||||||
|
|
||||||
@ -140,6 +170,27 @@ For this to work you will need to supply the device id as a parameter in the req
|
|||||||
http://mygravity.local/api/factory?id=<mydeviceid>
|
http://mygravity.local/api/factory?id=<mydeviceid>
|
||||||
|
|
||||||
|
|
||||||
|
GET: /api/test/push
|
||||||
|
===================
|
||||||
|
|
||||||
|
Trigger a push on one of the targets, used to validate the configuration from the UI.
|
||||||
|
|
||||||
|
Requires to parameters to function /api/test/push?id=<deviceid>&format=<format>
|
||||||
|
|
||||||
|
* ``format`` defines which endpoint to test, valid values are; http-1, http-2, brewfather, influxdb, mqtt
|
||||||
|
|
||||||
|
The response is an json message with the following values.
|
||||||
|
|
||||||
|
* ``code`` is the return code from the push function, typically http responsecode or error code from mqtt library.
|
||||||
|
|
||||||
|
.. code-block:: json
|
||||||
|
|
||||||
|
{
|
||||||
|
"success": false,
|
||||||
|
"enabled": true,
|
||||||
|
"code": -3
|
||||||
|
}
|
||||||
|
|
||||||
POST: /api/config/device
|
POST: /api/config/device
|
||||||
========================
|
========================
|
||||||
|
|
||||||
@ -222,6 +273,7 @@ Payload should be in standard format used for posting a form. Such as as: `id=va
|
|||||||
id=ee1bfc
|
id=ee1bfc
|
||||||
voltage-factor=1.59
|
voltage-factor=1.59
|
||||||
temp-adjustment=0
|
temp-adjustment=0
|
||||||
|
ble=red
|
||||||
gyro-temp=off
|
gyro-temp=off
|
||||||
ota-url=http://192.168.1.50/firmware/gravmon/
|
ota-url=http://192.168.1.50/firmware/gravmon/
|
||||||
|
|
||||||
@ -291,7 +343,7 @@ The requests package converts the json to standard form post format.
|
|||||||
"http-push2": "",
|
"http-push2": "",
|
||||||
"http-push-h1": "",
|
"http-push-h1": "",
|
||||||
"http-push-h2": "",
|
"http-push-h2": "",
|
||||||
"http-push2-h1": "",
|
"http-push2-h1": ""
|
||||||
"http-push2-h2": "",
|
"http-push2-h2": "",
|
||||||
"brewfather-push": "",
|
"brewfather-push": "",
|
||||||
"influxdb2-push": "",
|
"influxdb2-push": "",
|
||||||
@ -318,6 +370,7 @@ The requests package converts the json to standard form post format.
|
|||||||
"voltage-factor": 1.59, # Default value for voltage calculation
|
"voltage-factor": 1.59, # Default value for voltage calculation
|
||||||
"temp-adjustment": 0, # If temp sensor needs to be corrected
|
"temp-adjustment": 0, # If temp sensor needs to be corrected
|
||||||
"gyro-temp": "on", # Use the temp sensor in the gyro instead (on/off)
|
"gyro-temp": "on", # Use the temp sensor in the gyro instead (on/off)
|
||||||
|
"ble": "red", # Enable ble on esp32
|
||||||
"ota-url": "" # if the device should seach for a new update when active
|
"ota-url": "" # if the device should seach for a new update when active
|
||||||
}
|
}
|
||||||
set_config( url, json )
|
set_config( url, json )
|
||||||
|
@ -22,7 +22,7 @@ copyright = '2021-2022, Magnus Persson'
|
|||||||
author = 'Magnus Persson'
|
author = 'Magnus Persson'
|
||||||
|
|
||||||
# The full version, including alpha/beta/rc tags
|
# The full version, including alpha/beta/rc tags
|
||||||
release = '0.8.0'
|
release = '0.9.0'
|
||||||
|
|
||||||
|
|
||||||
# -- General configuration ---------------------------------------------------
|
# -- General configuration ---------------------------------------------------
|
||||||
|
@ -59,6 +59,10 @@ URL: (http://gravmon.local/device)
|
|||||||
This is unique identifier for the device (ESP8266 id), this is required when using the API as an API Key to safeguard
|
This is unique identifier for the device (ESP8266 id), this is required when using the API as an API Key to safeguard
|
||||||
against faulty requests. This is the ESP8266 chip ID, so it should be unique.
|
against faulty requests. This is the ESP8266 chip ID, so it should be unique.
|
||||||
|
|
||||||
|
* **Platform:**
|
||||||
|
|
||||||
|
Used to show what chip this build is for, it can be esp8266 or esp32. Some features are only available on an ESP32 platform.
|
||||||
|
|
||||||
* **Average runtime:**
|
* **Average runtime:**
|
||||||
|
|
||||||
This shows the average time a gravity measurement takes. Under optimal setting this should be
|
This shows the average time a gravity measurement takes. Under optimal setting this should be
|
||||||
@ -257,9 +261,13 @@ Hardware Settings
|
|||||||
device is activated, since the gyro should be cool this is reflecting the surronding temperature. After it has
|
device is activated, since the gyro should be cool this is reflecting the surronding temperature. After it has
|
||||||
been running the value would be totally off.
|
been running the value would be totally off.
|
||||||
|
|
||||||
|
* **Bluetooth: (Only ESP32)**
|
||||||
|
|
||||||
|
If the build is using an ESP32 then you can send data over BLE, simulating a Tilt device. Choose the color that you want the device to simulate.
|
||||||
|
|
||||||
* **OTA URL:**
|
* **OTA URL:**
|
||||||
|
|
||||||
Should point to a URL where the firmware.bin file + version.json file are located.
|
Should point to a URL where the firmware.bin file + version.json file are located. For an ESP32 target the firmware should be named firmware32.bin.
|
||||||
|
|
||||||
For the OTA to work, place the following files (version.json + firmware.bin) at the location that you pointed out in OTA URL. If the version number in the json file is newer than in the
|
For the OTA to work, place the following files (version.json + firmware.bin) at the location that you pointed out in OTA URL. If the version number in the json file is newer than in the
|
||||||
code the update will be done during startup.
|
code the update will be done during startup.
|
||||||
|
20
src_docs/source/hardware.rst
Normal file
20
src_docs/source/hardware.rst
Normal file
@ -0,0 +1,20 @@
|
|||||||
|
.. _hardware:
|
||||||
|
|
||||||
|
Hardware
|
||||||
|
########
|
||||||
|
|
||||||
|
There are lots of resouces out there on how to build the hardware for an iSpindle so I will not go into details on that part. Here are two of my builds using the iSpindle PCB v4.
|
||||||
|
|
||||||
|
.. image:: images/ispindel.jpg
|
||||||
|
:width: 500
|
||||||
|
:alt: Builds of iSpindel
|
||||||
|
|
||||||
|
It's possible to use this PCB and mount an ESP32 on top of that. It must be an pin compatible ESP32 and the one I used was called *ESP32 d1 mini*. Since this is the same width as the PCB you need to
|
||||||
|
mount it really close to the PCB in order for it to fit in the PET tube/container. I also had to smooth the edge of the ESP32 in order for it to fit.
|
||||||
|
|
||||||
|
I would suggest that you try how it fits into the PET tube before soldering it to the PCB. Make sure that the battery is attached since this will be a really tight fit.
|
||||||
|
|
||||||
|
.. image:: images/esp32.jpg
|
||||||
|
:width: 500
|
||||||
|
:alt: Mounting esp32
|
||||||
|
|
BIN
src_docs/source/images/esp32.jpg
Normal file
BIN
src_docs/source/images/esp32.jpg
Normal file
Binary file not shown.
After Width: | Height: | Size: 931 KiB |
BIN
src_docs/source/images/ispindel.jpg
Normal file
BIN
src_docs/source/images/ispindel.jpg
Normal file
Binary file not shown.
After Width: | Height: | Size: 2.5 MiB |
@ -7,7 +7,7 @@ Welcome to GravityMon's documentation!
|
|||||||
######################################
|
######################################
|
||||||
|
|
||||||
.. note::
|
.. note::
|
||||||
This documentation reflects **v0.8**. Last updated 2022-03-05
|
This documentation reflects **v0.9**. Last updated 2022-03-12
|
||||||
|
|
||||||
GravityMon is used to measure gravity and temperature during fermentation of beer and report the progress. The graph below is
|
GravityMon is used to measure gravity and temperature during fermentation of beer and report the progress. The graph below is
|
||||||
an example on how the fermentation process can be tracked. This is from my last brew that was over on a few days. The graph is rendered using
|
an example on how the fermentation process can be tracked. This is from my last brew that was over on a few days. The graph is rendered using
|
||||||
@ -21,6 +21,8 @@ GravityMon is a replacement firmare for the iSpindle and uses the same hardware
|
|||||||
implements a lot of the features that has been requested in the orginal iSpindle project but has been rejected for
|
implements a lot of the features that has been requested in the orginal iSpindle project but has been rejected for
|
||||||
various reasons. Here is a list of :ref:`main_features`.
|
various reasons. Here is a list of :ref:`main_features`.
|
||||||
|
|
||||||
|
From v0.9 the firmware now supports a iSpindle build based on an ESP32 d1 mini (pin compatible with esp8266). See :ref:`hardware`.
|
||||||
|
|
||||||
I started GravityMon because i like to create software and wanted to do some low level programming. I had done a few
|
I started GravityMon because i like to create software and wanted to do some low level programming. I had done a few
|
||||||
projects based on esp8266 and also started to brew beer so this combination was quite natural.
|
projects based on esp8266 and also started to brew beer so this combination was quite natural.
|
||||||
|
|
||||||
@ -124,17 +126,29 @@ the following libraries and without these this would have been much more difficu
|
|||||||
|
|
||||||
CSS templates for the web page.
|
CSS templates for the web page.
|
||||||
|
|
||||||
|
* https://github.com/lorol/LITTLEFS
|
||||||
|
|
||||||
|
LittleFS library for ESP32 framework 1.x
|
||||||
|
|
||||||
|
* https://github.com/h2zero/NimBLE-Arduino
|
||||||
|
|
||||||
|
Bluetooth library for ESP32 framework 1.x
|
||||||
|
|
||||||
|
* https://github.com/spouliot/tilt-sim
|
||||||
|
|
||||||
|
Excellent project for simulating a tilt device.
|
||||||
|
|
||||||
.. toctree::
|
.. toctree::
|
||||||
:maxdepth: 2
|
:maxdepth: 2
|
||||||
:caption: Contents:
|
:caption: Contents:
|
||||||
|
|
||||||
license
|
|
||||||
functionallity
|
|
||||||
intro
|
intro
|
||||||
installation
|
|
||||||
releases
|
releases
|
||||||
|
functionallity
|
||||||
|
installation
|
||||||
configuration
|
configuration
|
||||||
|
troubleshooting
|
||||||
|
q_and_a
|
||||||
formula
|
formula
|
||||||
services
|
services
|
||||||
advanced
|
advanced
|
||||||
@ -142,8 +156,8 @@ the following libraries and without these this would have been much more difficu
|
|||||||
data
|
data
|
||||||
compiling
|
compiling
|
||||||
contributing
|
contributing
|
||||||
troubleshooting
|
hardware
|
||||||
q_and_a
|
license
|
||||||
|
|
||||||
Indices and tables
|
Indices and tables
|
||||||
==================
|
==================
|
||||||
|
@ -3,6 +3,16 @@
|
|||||||
Releases
|
Releases
|
||||||
########
|
########
|
||||||
|
|
||||||
|
v0.9.0
|
||||||
|
------
|
||||||
|
* Added function to test push targets from configuration page. It will send data and show the return code as a first step.
|
||||||
|
* Updated WifiManager and DoubleReset libraries
|
||||||
|
* Experimental release of firmware using an esp32 instead of esp8266
|
||||||
|
* Updated esp32 target with littlefs support
|
||||||
|
* Updated esp32 target with BLE send support (it will simulate a tilt)
|
||||||
|
* Corrected PIN for voltage read on ESP32
|
||||||
|
* Mounted esp32 d1 mini mounted to a iSpindle PCB 4.0 (CherryPhilip) which worked fine.
|
||||||
|
|
||||||
v0.8.0
|
v0.8.0
|
||||||
------
|
------
|
||||||
|
|
||||||
|
Loading…
Reference in New Issue
Block a user